Category: Benzisoxazole

The molecularity of an elementary reaction is the number of molecules that collide during that step in the mechanism. 719-64-2, If there is only a single reactant molecule in an elementary reaction, that step is designated as unimolecular.5-Chloro-3-phenylbenzo[c]isoxazole, cas is 719-64-2,the Benzisoxazole compound. A new synthetic method of this compound is introduced below.

1) Weigh 180 g of raw material 5-chloro-3-phenyl-2,1-benzisoxazole into 1.5 L of anhydrous methanol and 1.5 L of acetonitrile,After stirring and dissolving, add 10g Pd/C catalyst with Pd content of 3%, stir and mix to form material I,The flow rate of the slurry pump was adjusted so that the flow rate of the material I was 40.0 g/min and entered the preheating module of the microreactor. 2) Adjust the flow rate of the H2 gas flowmeter to 350ml/min, and directly enter the reaction module group and material I to undergo catalytic hydrogenation reaction without preheating.As shown in Figure 2, the molar ratio of 5-chloro-3-phenyl-2,1-benzisoxazole to hydrogen is 1:1.2, the reaction temperature is 80C, the residence time of the reaction is 35s, and the reaction pressure is 1.0Mpa; then enter the cooling module, cooling module temperature is 30 C,Collect the reaction solution from the outlet of the cooling module, recover the catalyst by filtration, and recover the solvent by distillation under reduced pressure.The residue was recrystallized from 80% ethanol solution to obtain the target product 2-amino-5-chlorobenzophenone, 168.96g, yield 92.79%, purity 99.68%.

719-64-2, A chemical reaction often occurs in steps, although it may not always be obvious to an observer. Thank you very much for taking the time to read this article. If you are also interested in other aspects of 719-64-2, you can also browse my other articles.

Reference£º
Patent; Heilongjiang Xinchuang Bio-technology Development Co., Ltd.; Ren Jiqiu; Yang Kun; Li Haitao; (10 pag.)CN107935872; (2018); A;,
Benzisoxazole – Wikipedia
Benzisoxazole – an overview | ScienceDirect Topics

The molecularity of an elementary reaction is the number of molecules that collide during that step in the mechanism. If there is only a single reactant molecule in an elementary reaction, that step is designated as unimolecular.5-Amino-3-methylbenzo[d]isoxazole, cas is 851768-35-9,the Benzisoxazole compound. A new synthetic method of this compound is introduced below. 851768-35-9

Synthesis of 3-chloro-2-methyl-N-(3-methyl-benzo[d]isoxazol-5-yl)- benzenesulfonamide, STX 874 (KRB01027):; To a solution of 3-chloro-2-methylbenzenesulphonyl chloride (128 mg, 0.567 mmol) in dichloromethane (3 mL) was added pyridine (110 muL, 1.35 mmol) and the mixture was stirred under N2 for 5 min, after which time 5-amino-3-methyl-1, 2-benzisoxazole [26] (80 mg, 0.54 mmol) was added. The resulting mixture was stirred for 4 h at room temperature, then saturated NaHCO3 solution (8 mL) was added and the mixture was extracted into ethyl acetate (15 mL). The organic phase was washed with brine, dried (Na2SO4), filtered and evaporated to give a residue that was purified using flash chromatography to afford a white solid (88 mg, 48%), single spot at Rf 0.58 (1: 1 hexane: ethyl acetate). mp 162.8-163. 2C, HPLC purity 99+% (tR 2.26 min in 10% water- acetonitrile).’H NMR (CDC13) : 6 7.80 (1H, dd, J=7.9, 1.3 Hz), 7.55 (1H, dd, J=8. 1, 1.1 Hz), 7.38 (2H, m), 7.17 (1 H, t, J=8.1 Hz), 7.10 (1H, dd, J=8.8, 2.2 Hz), 6.72 (1H, s, N-lez 2.72 (3H, s), 2.50 (3H, s). LCMS: 320.00 (M-CH3). FAB-MS (MH+, C15H13ClN2O3S) : calcd 337.0413, found 337.0422.

851768-35-9, There are, however, a few established termolecular elementary reactions. The reaction of nitric oxide with oxygen appears to involve termolecular steps. you can also browse my other articles about 851768-35-9

Reference£º
Patent; STERIX LIMITED; WO2005/42513; (2005); A1;,
Benzisoxazole – Wikipedia
Benzisoxazole – an overview | ScienceDirect Topics

A balanced equation for a chemical reaction indicates what is reacting and what is produced, but it reveals nothing about how the reaction actually takes place. The reaction mechanism is the process, or pathway, by which a reaction occurs.Benzo[d]isoxazol-3-amine, cas is 36216-80-5,the Benzisoxazole compound. An updated downstream synthesis route of 36216-80-5 as follows. 36216-80-5

A mixture of benzo[d]isoxazol-3-amine and a sulfonyl chloride in pyridine (0.5 ml.) was stirred at room temperature for 16 hours. The reaction was concentrated and diluted with 5% aqueous HCI (1 ml.) and sonicated for a minimum of 30 minutes. The resulting precipitate was collected by filtration and a portion of the crude material (50 mg or less) was purified by mass directed preparative HPLC to give the desired product. See Table B for reaction components and amounts used., 36216-80-5

Any one of these steps may be slow and thus may serve as the rate determining step. In general, however, in the presence of the catalyst, the overall rate of the reaction is faster than it would be if the reactants were in the gas or liquid phase., 36216-80-5

Reference£º
Patent; CTXT PTY LIMITED; STUPPLE, Paul, Anthony; LAGIAKOS, Helen, Rachel; MORROW, Benjamin, Joseph; FOITZIK, Richard, Charles; HEMLEY, Catherine, Fae; CAMERINO, Michelle, Ang; BOZIKIS, Ylva, Elisabet, Bergman; WALKER, Scott, Raymond; (321 pag.)WO2019/243491; (2019); A1;,
Benzisoxazole – Wikipedia
Benzisoxazole – an overview | ScienceDirect Topics

239097-74-6, Rate laws may be derived directly from the chemical equations for elementary reactions. This is not the case, however, for ordinary chemical reactions.Benzo[d]isoxazol-5-amine, cas is 239097-74-6,the Benzisoxazole compound, below Introduce a new synthetic route.

To a suspension of the ester compound from the procedure above (105 mg, 0.340 mmol) in DMF (0.5 mL) was added a solution of l,2-benoxazol-5-amine (46 mg, 0.340 mmol) in DMF (0.5 mL). The reaction mixture was stirred at room temperature for 2 hours until the reaction was complete, and quenched with the addition of TFA (5 drops). The precipitated solid was collected by filtration, suspended in DCM, basified with saturated aHC03to pH ~8. The aqueous layer was extracted with DCM, dried over anhydrous a2S04, filtered andconcentrated to provide a residue. The residue was purified by prep-HPLC (MeCN/H20) to provide the title compound (40 mg, 38%) as a white solid.XH NMR (400 MHz, CDC13) delta 10.31 (s, 1H), 8.72-8.71 (m, 2H), 8.45 (d, J= 1.6 Hz, 1H), 7.67 (dd, J= 9.2 Hz, 2.0 Hz, 1H), 7.60 (d, J= 9.2 Hz, 1H), 6.79 (s, 1H), 2.84 (s, 3H), 2.74 (s, 3H). ES-MS m/z: 308.0 [M+H]+. HPLC Purity (214 nm): 98%; tR= 9.36 min.

In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles. 239097-74-6, other downstream synthetic routes, hurry up and to see.

Reference£º
Patent; LYSOSOMAL THERAPEUTICS INC.; SKERLJ, Renato, T.; LANSBURY, Peter, T.; GOOD, Andrew, C.; BOURQUE, Elyse, Marie Josee; (139 pag.)WO2016/73895; (2016); A1;,
Benzisoxazole – Wikipedia
Benzisoxazole – an overview | ScienceDirect Topics

One of the major reasons is to use measurements of the macroscopic properties of a system, 36216-80-5, such as the rate of change in the concentration of reactants or products with time, to discover the sequence of events that occur at the molecular level.Benzo[d]isoxazol-3-amine, cas is 36216-80-5,the Benzisoxazole compound, introduce a new downstream synthesis route.

(2) Bis(2,2,2-trichloroethyl) 1,2-benzisoxazol-3-ylimidodicarbonate; To a solution of 1,2-benzisoxazol-3-amine (4.00 g, 29.8 mmol) and pyridine (7.25 ml, 89.6 mmol) in tetrahydrofuran (100 ml) was added under ice-cooling, 2,2,2-trichloroethyl chloroformate (8.20 ml, 59.6 mmol), and the mixture was stirred under ice-cooling for 1 hour and at room temperature for 20 minutes. The reaction mixture was poured to water and extracted with ethyl acetate. The extract was washed with water and dried over anhydrous magnesium sulfate, and the solvent was distilled off under reduced pressure. To the residue was added hexane to give 13.3 g (91.7%) of the desired product as a solid. 1H-NMR (CDCl3) delta; 4.82 (4H, s), 7.36 – 7.44 (1H, m), 7.59 – 7.65 (3H, m).

Any one of these steps may be slow and thus may serve as the rate determining step. In general, however, in the presence of the catalyst, the overall rate of the reaction is faster than it would be if the reactants were in the gas or liquid phase., 36216-80-5

Reference£º
Patent; Takeda Pharmaceutical Company Limited; EP1813606; (2007); A1;,
Benzisoxazole – Wikipedia
Benzisoxazole – an overview | ScienceDirect Topics

One of the major reasons is to use measurements of the macroscopic properties of a system, 37924-85-9, such as the rate of change in the concentration of reactants or products with time, to discover the sequence of events that occur at the molecular level.3-(Bromomethyl)benzo[d]isoxazole, cas is 37924-85-9,the Benzisoxazole compound, introduce a new downstream synthesis route.

General procedure: To NaOMe (25% soln, 0.5 mL, 2.2 mmol) in MeOH (5 mL) was added thiosemicarbazide 9 (200 mg, 2.2 mmol). Diethyloxalate (0.3 mL, 2.2 mmol) was then added dropwise. The mixture was heated at 65 C for 2 h and then cooled to rt. 1-(Bromomethyl)-4-chlorobenzene (500 mg, 2.4 mmol) was added in one portion; stirring was continued at rt for 3 h and then heated overnight at 50 C. The reaction mixture was concentrated. The residue was dissolved in EtOAc (40 mL), washed with water (20 mL), and brine (20 mL). The organic phase was dried over Na2SO4, concentrated and purified by silica gel column chromatography (EtOAc w/ 0.2% HOAc). The product was triturated in Et2O to afford 59 mg of 6g as a light yellow solid (10% yield)

Any one of these steps may be slow and thus may serve as the rate determining step. In general, however, in the presence of the catalyst, the overall rate of the reaction is faster than it would be if the reactants were in the gas or liquid phase., 37924-85-9

Reference£º
Article; Hin, Niyada; Duvall, Bridget; Berry, James F.; Ferraris, Dana V.; Rais, Rana; Alt, Jesse; Rojas, Camilo; Slusher, Barbara S.; Tsukamoto, Takashi; Bioorganic and Medicinal Chemistry Letters; vol. 26; 8; (2016); p. 2088 – 2091;,
Benzisoxazole – Wikipedia
Benzisoxazole – an overview | ScienceDirect Topics

651780-27-7, Rate laws may be derived directly from the chemical equations for elementary reactions. This is not the case, however, for ordinary chemical reactions.Ethyl 6-bromobenzo[d]isoxazole-3-carboxylate, cas is 651780-27-7,the Benzisoxazole compound, below Introduce a new synthetic route.

To a mixture of ethyl 6-bromobenzisoxazole-3-carboxylate (2.0 g, 7.4 mmol) and t- butyl 5-cyanoanthranilate (1.62 g, 7.4 mmol) in toluene (27 [ML)] is added NaH (1.5 g of a 60% mineral oil dispersion, 3.8 mmol) under N2. The reaction mixture is stirred overnight at rt. This mixture is diluted with aq 1 N [HCI,] extracted with EtOAc (0.2 L). The EtOAc solution is dried and concentrated to give Preparation Pb as a solid : 1H NMR (300 MHz, CDC13) [8] 12.8 (1H), 9.05 [(1H),] 8.38 (1H), 8.18 (1H), 7.92 (1H), 7.82 (1H), 7.61 [(1H),] [1.] 69 [(9H).]

According to the analysis of related databases, Ethyl 6-bromobenzo[d]isoxazole-3-carboxylate, the application of this compound in the production field has become more and more popular.

Reference£º
Patent; PHARMACIA & UPJOHN COMPANY; WO2004/18428; (2004); A1;,
Benzisoxazole – Wikipedia
Benzisoxazole – an overview | ScienceDirect Topics

An elementary termolecular reaction involves the simultaneous collision of three atoms, molecules, or ions.3,6-Dichlorobenzo[d]isoxazole, cas is 16263-54-0,the Benzisoxazole compound. 16263-54-0. Here is a downstream synthesis route of the compound 16263-54-0

To a solution of l-Boc-5-trifluoromethoxybenzimidazole-2-one (5 g, 15.7 mmol) in DMF (20 ml) was added 3,6-dichlorobenzoisoxazole (3.0 g, 15.7 mmol) and Cs2CO3 (11 g, 31.4 mmol). The suspension was heated to 15O0C in an oil bath and stirred overnight. The mixture was then cooled to room temperature, diluted with water (30 ml) and extracted with ethyl acetate (2×20 ml). The organic extracts were combined, dried over anhydrous Mg2SO4, and concentrated to dryness. The residue was purified by silica gel column chromatography using hexane/ethyl acetate (4:1) as solvent system. Fractions containing earlier eluted product were combined and concentrated to obtain l-[3-(6-chloro)-benzisoxazoyl]-5- trifluoromethoxylbenzimidazole-2-one as a white solid. 1H NMR (DMSO, 500 MHz) delta 8.28 (d, J=9.0Hz, IH), 8.12 (s, IH), 7.74 (d, J=9.0Hz, IH), 7.54 (d, J=8.5, IH), 7.14 (d, J=8.5, IH), 7.13 (s, IH). Fractions containing later eluted product were combined and concentrated to obtain l-[3-(6-chloro)-benzisoxazoyl]-6-trifluoromethoxylbenzimidazole-2-one as a white solid. 1H NMR (DMSO, 500 MHz) delta 8.28 (d, J=9.0Hz, IH), 8.12 (s, IH), 7.74 (d, J=9.0Hz, IH), 7.66 (brs, IH), 7.54 (d, J=8.5, IH), 7.13 (brs, IH).

16263-54-0. Other significant industrial processes that involve the use of heterogeneous catalysts include the preparation of sulfuric acid, the preparation of ammonia, the oxidation of ammonia to nitric acid, and the synthesis of methanol.16263-54-0, if you are interested, you can browse my other articles.

Reference£º
Patent; MERCK & CO., INC.; WO2006/22954; (2006); A2;,
Benzisoxazole – Wikipedia
Benzisoxazole – an overview | ScienceDirect Topics

Rate laws may be derived directly from the chemical equations for elementary reactions. This is not the case, however, for ordinary chemical reactions.3,6-Dichlorobenzo[d]isoxazole, cas is 16263-54-0,the Benzisoxazole compound, below Introduce a new synthetic route., 16263-54-0

5) Preparation 6-chloro-3-piperazinyl-benzisoxazole 3,6-dichlorobenzisoxazole (5.2g, 27.8 mmol), and anhydrous piperazine (24g, 278 mmol) are placed in an egg type flask and react at 120C for 24 hours. After completion of the reaction, 52 ml of an ice-water mixture is added for quenching the reaction. Further 15 ml of 50% NaOH solution is added to the reaction solution. The reaction solution is stirred for 5 minutes and extracted with dichloromethane (30ml*3). The dichloromethane layer is combined, washed with 20 ml of saturated saline, dried over anhydrous MgSO4, evaporated to dryness, and subjected to a separation on a column of alumina (200-300mesh), eluting with dichloromethane_methanol=100:1, to obtain 4.7g of 6-chloro-3-piperazinyl-benzisoxazole, with a yield of 71%.

At the same time, in my other blogs, there are other synthetic methods of this type of compound, 3,6-Dichlorobenzo[d]isoxazole, and friends who are interested can also refer to it.

Reference£º
Patent; Jiangsu Guohua Investment Co., Ltd; Shanghai Institute of Pharmaceutical Industry; EP2322520; (2011); A1;,
Benzisoxazole – Wikipedia
Benzisoxazole – an overview | ScienceDirect Topics

36216-80-5, An elementary termolecular reaction involves the simultaneous collision of three atoms, molecules, or ions.Benzo[d]isoxazol-3-amine, cas is 36216-80-5,the Benzisoxazole compound. Here is a downstream synthesis route of the compound 36216-80-5

General procedure: To a stirred solution of pyridin-2-amine (1.0 g, 10.6 mmol) and pyridine (1.01 mL, 12.7 mmol) in THF (35 mL) was added 2,2,2- trichloroethyl chloroformate (1.76 mL, 12.7 mmol) dropwise at 0 C. The mixture was stirred at 0 C for 1.5 h, poured into water, and extracted with EtOAc. The organic layer was washed with water, dried over anhydrous MgSO4, and concentrated in vacuo. The residue was triturated with Et2O-hexane to give 36 (1.76 g, 62%) as a colorless powder.

36216-80-5. Other significant industrial processes that involve the use of heterogeneous catalysts include the preparation of sulfuric acid, the preparation of ammonia, the oxidation of ammonia to nitric acid, and the synthesis of methanol.36216-80-5, if you are interested, you can browse my other articles.

Reference£º
Article; Kono, Mitsunori; Matsumoto, Takahiro; Kawamura, Toru; Nishimura, Atsushi; Kiyota, Yoshihiro; Oki, Hideyuki; Miyazaki, Junichi; Igaki, Shigeru; Behnke, Craig A.; Shimojo, Masato; Kori, Masakuni; Bioorganic and Medicinal Chemistry; vol. 21; 1; (2013); p. 28 – 41;,
Benzisoxazole – Wikipedia
Benzisoxazole – an overview | ScienceDirect Topics